Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
This post down below involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is rather remarkable. Read on and make your own conclusions.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Setting up a tub isn't specifically rocket science, but it does require strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably difficult project. If the old bathtub is readily easily accessible, the job can move easily; if you have to open up a wall surface to remove the old tub and also place the new bath tub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will need an assistant to leave the old bathtub and also embeded in the brand-new one. See to it you have certified on your own for the job as well as are comfortable attempting it. Rather than employing a professional to take over a halfway-completed job, it is better to consider using one before you start. Possibilities are you might need an expert plumber to make tube connections.
This post will certainly assist you mount a brand-new bathtub in your washroom if you have actually currently bought a brand-new bathtub as well as don't require to alter the setup of your previous water pipes.
Your devices and also material list need to comprise the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be quite troublesome as a result of the limited accessibility that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making sure that the washers are in area in between the faucet as well as the sink. Protect the faucet in position with the supplier supplied backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet connectors. The former type ought to be attached to the faucet finishes initially, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Using the two wooden boards under its feet, place the tub in the called for placement. The wood boards are handy in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and adjusting the feet on the bath tub till the level reviews degree.
To install taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipe by making a compression sign up with; then do the very same for the various other tap.
Activate the water system and also examine all joints and new pipework for leaks and also tighten them if required. Fill up the bathtub and additionally check the overflow electrical outlet and the normal electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the maker's user's manual. Tiling and sealing around the bath tub must wait until the bathtub has actually been made use of at least once as this will settle it right into its final position.
Preparing for the Installation
First of all, the supporting structure supplied with the bathroom needs to be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to avoid pressure on the bathtub.
Fit the adaptable tap ports to the bottom of both taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, triggering the water to pass through the wall surface in between the bath and the tiling, causing difficulties with wetness and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to enable the movement experienced when the tub is in use. The sealant can fracture rather early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily available on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very fascinated with How to Install a Bathtub Yourself and I'm hoping you appreciated our blog posting. Liked our piece of writing? Please share it. Let someone else check it out. We take joy in reading our article about How to Install a Bathtub.
Click Here To Read More Report this page